2019 Engine Master's Challenge - Studebaker Power Team

THE place to document, in chronological order, ON-GOING progress/milestones of ANY high performance Studebaker project. Projects include any major/lengthy - repair/modification/resto/total rebuild OR an extensive build/development/modification of a high performance Studebaker part/system. Including as much info/many photos about/of your project is greatly appreciated! ON-GOING PROJECTS ONLY PLEASE.
Post Reply
User avatar
Jeff Rice
Global Moderator
Posts: 4809
Joined: 15 Jan 2004, 08:48
Location: Brooklet, Georgia,USA,Earth
Contact:

Re: 2019 Engine Master's Challenge - Studebaker Power Team

Post by Jeff Rice » 06 Oct 2019, 20:21

No, Jack.. They never asked, or measured.

User avatar
Jeff Rice
Global Moderator
Posts: 4809
Joined: 15 Jan 2004, 08:48
Location: Brooklet, Georgia,USA,Earth
Contact:

Re: 2019 Engine Master's Challenge - Studebaker Power Team

Post by Jeff Rice » 06 Oct 2019, 20:27

Carnut1Cars wrote:
06 Oct 2019, 17:00
<snip> Any chance we could get the max advance numbers? Just as a ballpark as I am setting up a similar distributor.
Remember, this is a dyno engine.
Mechanical advance 'all in' at 3,000 rpm.
No vacuum advance.

Timing is engine specific, and each engine will tell you what it wants, depending on fuel and load and atmospheric conditions.
If I told you a number and you used it, it could be all wrong for your engine.
Let us say that we started at 25 degree's and went up from there...

diggerdavem
100 - 199 Posts
Posts: 193
Joined: 19 Nov 2010, 09:22

Re: 2019 Engine Master's Challenge - Studebaker Power Team

Post by diggerdavem » 07 Oct 2019, 10:58

Thanks for the externally adjustable metering block info. We ended with 38 degrees total distributor timing, a lot for a Studebaker V/8 but on the dyno power kept increasing from starting point of 25 degrees. We did 21 dyno pulls and added one to two degrees at a time and power increased each time, so I don't know what is max at this time with this engine. Maybe it was the fuel that allowed this to happened. Running on the dyno and down the drag strip are two different things so I don't recommend doing this. Compression ratio 10.3.

Jack the pushrods are from Trend.

diggerdave

3x2stude
Studebaker Racing Team Member
Posts: 436
Joined: 21 May 2012, 19:24

Re: 2019 Engine Master's Challenge - Studebaker Power Team

Post by 3x2stude » 08 Oct 2019, 21:44

Dave,

Let me know if you need anything next year. I am sending a PM in minute or two.

JK

diggerdavem
100 - 199 Posts
Posts: 193
Joined: 19 Nov 2010, 09:22

Re: 2019 Engine Master's Challenge - Studebaker Power Team

Post by diggerdavem » 09 Oct 2019, 12:53

JK
Thank you for your fine work on the windage tray. was not able to use the scrapers and will return to you. The oil pan was used with 5 qts. 15/50 Amsoil after break-in oil 30w removed. We have to wait for new 2020 rules. Hope to use same engine again with modifications.
Thank you again
diggerdave

3x2stude
Studebaker Racing Team Member
Posts: 436
Joined: 21 May 2012, 19:24

Re: 2019 Engine Master's Challenge - Studebaker Power Team

Post by 3x2stude » 11 Oct 2019, 23:13

Dave,

Sending another PM in a minute.

JK

User avatar
Jeff Rice
Global Moderator
Posts: 4809
Joined: 15 Jan 2004, 08:48
Location: Brooklet, Georgia,USA,Earth
Contact:

Re: 2019 Engine Master's Challenge - Studebaker Power Team

Post by Jeff Rice » 16 Oct 2019, 11:06

Great news!
Due to numerous requests, we are running a new batch of button down 2019 Engine Masters Studebaker Power team shirts to be offered up for sale to the supporters and enthusiasts of the Studebaker Power Team.
Will have pricing available soon. There will be three changes made from the original art work.
(1) No monogram offered (to keep cost down)
(2) No flag sewn on sleeve* (to keep cost down)
* I will put a loose flag in the box upon request.
(3) (to be announced)

Pre-orders needed now so quantities can be estimated and an accurate price can be quoted.
"Should" be in the $40 to $45 range (less if I can get some quantity breaks).
Will need your address so freight out can be accurately quoted. 
Will ship these direct from the printer to avoid double freight out charges (to keep cost's down).

These are great shirts that can be worn with pride! 

Image

Sarge approved!

Image

You can PM me here, or send an e-mail to DEEPNHOCK at gmail dot com

User avatar
Jeff Rice
Global Moderator
Posts: 4809
Joined: 15 Jan 2004, 08:48
Location: Brooklet, Georgia,USA,Earth
Contact:

Re: 2019 Engine Master's Challenge - Studebaker Power Team

Post by Jeff Rice » 21 Oct 2019, 11:03

10/21/2019 Update.......

(10/21/2019)
Team Supporter shirt follow up.
Have surpassed the minimum quantity order level for the Hot Rod Magazine Engine Masters Team Supporter shirts.
This is great news!
So, to keep things timely, we are going to give this just a few more days until we cut off the orders and get making shirts!

If you would like a snazzy team supporter shirt, let me know via a PM..
Pricing to follow, but we expect it to be in the $40 to $45 range, plus postage out.

If you have already contacted me to get one of these shirts, you should have already received a PM response. If you didn't get one, let me know.
Thanks!
Jeff


Image

User avatar
Jeff Rice
Global Moderator
Posts: 4809
Joined: 15 Jan 2004, 08:48
Location: Brooklet, Georgia,USA,Earth
Contact:

Re: 2019 Engine Master's Challenge - Studebaker Power Team

Post by Jeff Rice » 25 Oct 2019, 19:47

Studebaker Power Team Supporter Shirt Order Window Is Closed.

Thank you soooo much for your support.
Look forward to being contacted with the amount and the postage as soon as I get the numbers back

Jeff

Post Reply